Home / News / Drill Parts of Horsch

Drill Parts of Horsch

August 13, 2026 • 2 min read
Share:
Drill Parts of Horsch
CodeDescriptionSizeOEM Number
AMP614MXPMXP Dutch Opener Point 5" OEM (2827)- Double

Maxipart® 5” Dutch Opener Tungsten (Double)

1. High Chrome content for extended wear life.
2. Extended front tungsten tile for additional protection.
3. Wing tungsten closer to tip.
4. Added bolt hole protection.

OEM(SWB443)
AMP615MXPMXP Dutch Opener Point 1" OEM(2837) - Single

Maxipart® 1” Dutch Opener Tungsten (Single)

1. High Chrome content for extended wear life.
2. Extended front tungsten tile for additional protection.
3. Wing tungsten closer to tip.
4. Added bolt hole protection.

OEM(SWB444)
AMP618MXPMXP Dutch Opener Point 2" OEM(2839) - Single

Maxipart® 2” Opener Tungsten (Single)

1. High Chrome content for extended wear life.
2. Extended front tungsten tile for additional protection.
3. Wing tungsten closer to tip.
4. Added bolt hole protection.

OEM(2839)
AMP620MXPMXP Dutch Opener Point 5" OEM(2845) - Single

Maxipart® 5” Dutch Opener Tungsten (Single)

1. High Chrome content for extended wear life.
2. Extended front tungsten tile for additional protection.
3. Wing tungsten closer to tip.
4. Added bolt hole protection.

OEM(2845)
AMP621MXPMXP Dutch Opener Point 3" OEM(2841) - Single

Maxipart® 3" Dutch Opener Point Tungsten (Single):

1. High Chrome content for extended wear life.
2. Extended front tungsten tile for additional protection.
3. Wing tungsten closer to tip.
4. Added bolt hole protection.

 

 

OEM(2841)
AMC30125MXPMXP Horsch Direct Drill Tine OEM()

Maxipart® Direct Drill Point
AMC30125MXP to fit Horsch Co & Sprinters

1. 12mm leading edge for hugely reduced fuel and horsepower requirement.
2. Reduced width means far less disturbance.
3. 130mm of tungsten up leading edge to extend working life.
4. Tungsten placement prevents trash “hooking” around the tine, allowing surface material to flow through the legs.
5. Hard facing on the side and underside helps protect integral seed plates.
6. Splayed seed plates at the rear to ensure free flow of seed, reducing bridging and thus blockages.

AMP759MXPMXP Horsch Drill Point Tgstn-1 OEM(00310262)

Maxipart® Point Tungsten x1
1. High chrome content for extended wear life.

OEM(00310262)
AMP740MXPMXP Horsch Drill Point Tgstn-2 OEM(00310262)

Maxipart® Point Tungsten x2
1. High chrome content for extended wear life.

OEM(00310262)
AMP741MXPMXP Horsch Base Plate 170mm OEM(00310656)

Maxipart® Base Plate 170mm
1. High chrome content for extended wear life.

OEM (00310656)
AMP752Horsch Base Plate 200mm OEM (00310897)

Base Plate 200mm

200 mmOEM (00310897)
AMP744MXPMXP Horsch Base Plate 170 Tgst OEM (00310656)

Maxipart® Base Plate 170mm Tungsten
1. High chrome content for extended wear life.

OEM (00310656)
AMP745MXPMXP Horsch Base Plate 200 Tgst OEM (00310897)

Maxipart® Base Plate 200mm Tungsten
1. High chrome content for extended wear life.

OEM (00310897)
AMP748Horsch Single Following Tine OEM(00310081)

Following Tine Rear 490mm x 12mm

OEM(00310081)
AMP747Horsch Double Covering Tine OEM(00430507)


Double Covering Tine (12mm Thick)

430507
AMP749Horsch Double Following Tine OEM(34217502)


Double Following Tine (12mm thick)

OEM(34217502)
AMP749MXPMXP C60 Horsch Following Tine OEM(34217502)

By using a specialised High Carbon steel, the C60 range allows for the tines to retain optimum flexibility where needed, whilst heat treating the wear tips so that they reach a hardness in excess of 60HRC.

Resulting in an unrivalled high quality performance with maximum wear life.

APX300Key Nut with Collar M10 OEM(33010103)
M10OEM(33010103)

Share this article

More from Dawopu